應社友要求，共享SW鈑金零件輸出展開DWG的代碼

DaveChan · 發表于 2016-10-23 10:39:59

保留折彎線:

Option Explicit
) |% H4 A6 ^* \* [8 j
Dim swApp As SldWorks.SldWorks( n6 x# g: P9 C: S+ |8 V
Dim swModel As SldWorks.ModelDoc2- F) Q: I$ a/ s3 A, F4 j6 F* ?8 k F* Y
Dim swModelDocExt As SldWorks.ModelDocExtension: x- r; c0 D! N" R4 ]5 M7 R
Dim FileName As String6 g5 I L1 ?! ^8 j. t. r
Dim NewName As String
- t+ Y1 A x- _0 ~( ?
Dim boolstatus As Boolean
: ]- ^* w- J. j6 Z5 k/ T, p
Dim longstatus As Long, longwarnings As Long
' h1 `8 k4 l8 D2 I- C# y$ c) |
Sub main(); [/ f6 f0 Z3 s1 R8 E, G
Set swApp = Application.SldWorks& H7 h" `$ Z( v, m
Set swModel = swApp.ActiveDoc% [* B! I3 X2 U6 X
Set swModelDocExt = swModel.Extension- l) ] \. u* b) d- k
FileName = swModel.GetPathName()
4 g( K7 S* A4 ^& h8 n$ i$ N
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"7 n; u4 X1 m D
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_None)
( L" i t, ]1 `' d. T
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings
6 G" i0 G8 U' J( A# }3 w. t
End Sub
; L* }) L8 G# s# Z

復制代碼

移除折彎線:

Option Explicit
9 T9 @) Y& {9 _, r# J
Dim swApp As SldWorks.SldWorks4 ?! _" |; S0 p: F) Q9 K
Dim swModel As SldWorks.ModelDoc2
7 T2 b) v9 w) X& L/ e1 o
Dim swModelDocExt As SldWorks.ModelDocExtension
$ \3 ]/ E: f( a# \7 j
Dim FileName As String. w) m) [$ a& A" B; F/ }+ u
Dim NewName As String
/ l+ }% k: N% p7 y
Dim boolstatus As Boolean
- n3 y1 \/ t7 v0 _9 C0 k$ ?
Dim longstatus As Long, longwarnings As Long
7 G7 W' I8 a4 _- r$ b! i
Sub main()
2 E1 Q D! n+ e9 `
Set swApp = Application.SldWorks
# P. X8 o1 t3 G$ I! F
Set swModel = swApp.ActiveDoc+ o( D2 q/ @" k- h
Set swModelDocExt = swModel.Extension0 _) x1 p: L- t1 I* F( Y& y; e
FileName = swModel.GetPathName()+ U% A( o/ z1 w8 l% N6 m
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"
: a# q/ T, n% j8 \
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_RemoveBends)
% v7 E7 D$ M. v+ ?
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings
* P& C- Y% { v" j
End Sub
$ Z" C3 ~" P/ H" K4 M3 d; m

復制代碼

響在江湖 · 發表于 2016-10-23 10:47:29

必須頂上去！超實用！！

小飛熊l · 發表于 2016-10-23 15:39:50

沒覺得sw鈑金需要改動啊

newmorn · 發表于 2016-10-23 16:56:57

sw工程圖里面的平板形式不就是展開圖嗎？這都要寫代碼呀？

機械路慢 · 發表于 2016-10-23 17:46:39

樓主，這是？代碼要放到哪里？

befuture · 發表于 2016-10-23 19:23:30

怎么用啊新手

hc2003 · 發表于 2016-10-23 19:49:24

樓主好人做到底，說明一下怎么使用啊

DaveChan · 發表于 2016-10-24 08:23:43

本帖最后由 DaveChan 于 2016-10-24 08:54 編輯

newmorn 發表于 2016-10-23 16:56$ ^2 }8 e* a( p S/ t2 ~
sw工程圖里面的平板形式不就是展開圖嗎？這都要寫代碼呀？

代碼替代了繁瑣的點擊另存為過程，利用代碼做成宏按鈕，一鍵保存平板形式為dwg/dxf下面動畫為另存為輸出過程和宏代碼輸出過程

DaveChan · 發表于 2016-10-24 08:58:37

hc2003 發表于 2016-10-23 19:495 u1 y: s' e/ N j+ B0 L
樓主好人做到底，說明一下怎么使用啊

1.新建一個宏，刪除里面所有代碼
2.復制我貼的代碼到這個宏里面
3.保存此宏
4.打開一個鈑金零件(可以展開的零件)
5.運行此宏
6.自動輸出展開圖(DWG)

		自動登錄	找回密碼
密碼			注冊會員

久久久国产一区二区_国产精品av电影_日韩精品中文字幕一区二区三区_精品一区二区三区免费毛片爱