應社友要求，共享SW鈑金零件輸出展開DWG的代碼

DaveChan · 發表于 2016-10-23 10:39:59

保留折彎線:

Option Explicit
2 b" E( g1 }1 U3 ]+ N6 C
Dim swApp As SldWorks.SldWorks7 [2 T( r" K w8 \$ C, l
Dim swModel As SldWorks.ModelDoc2
' h4 J& f, M& r- `3 A
Dim swModelDocExt As SldWorks.ModelDocExtension8 @$ w! }/ G, x( B
Dim FileName As String
. z6 y: h: K. E, f/ k: C3 Q
Dim NewName As String& r0 N: y0 `0 O4 T- I
Dim boolstatus As Boolean4 Q$ ]" B5 I" v/ R
Dim longstatus As Long, longwarnings As Long/ O+ @, y& i1 x; X0 ^. y8 s, f
Sub main()
: S) o: ]9 O& |* O7 B4 `( V0 |- g4 K5 P
Set swApp = Application.SldWorks: J& n) T V3 [) X8 Q* i' W
Set swModel = swApp.ActiveDoc) `; |1 l) E8 L* E' }
Set swModelDocExt = swModel.Extension4 i: K2 v( y& {! }2 y
FileName = swModel.GetPathName()
" _8 \, |3 b7 R# @. |3 t
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"
) ^7 x$ m. S" r! @" g! j; w! V
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_None)
$ k3 S$ n5 S' c9 H X* H; n% X
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings1 ?+ y7 w: B7 {" Q: a
End Sub
6 t( h; [: F& l. Q: C

復制代碼

移除折彎線:

Option Explicit5 i" l& ~3 m6 w; \
Dim swApp As SldWorks.SldWorks4 U, g; L! j8 P9 U0 `/ \
Dim swModel As SldWorks.ModelDoc2
' I/ L2 R, P2 g7 l Y
Dim swModelDocExt As SldWorks.ModelDocExtension
% `2 l) a, f- y/ { y i! n
Dim FileName As String
: h' X( D6 c. V
Dim NewName As String3 ]6 Z/ d' x7 s* @
Dim boolstatus As Boolean( o' |' h4 G. T, I- r
Dim longstatus As Long, longwarnings As Long2 n5 U" { M$ E" ^+ A$ y0 H5 t$ l0 ?
Sub main()7 A$ {# m; o4 E% _& z1 @1 A
Set swApp = Application.SldWorks1 C" |6 \9 M2 c& V
Set swModel = swApp.ActiveDoc
7 h/ ^& F, y4 {
Set swModelDocExt = swModel.Extension0 ~- P% Z5 f2 }& Z( z3 K7 ^
FileName = swModel.GetPathName()& K1 i$ V# S) ^/ M8 Q( p# F( h
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"
' g2 i1 b, E5 l- w; ~
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_RemoveBends)# _" n% }3 b% m @
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings6 ` a" G; C* p
End Sub3 e, f* J- A* m4 U4 x

復制代碼

響在江湖 · 發表于 2016-10-23 10:47:29

必須頂上去！超實用！！

小飛熊l · 發表于 2016-10-23 15:39:50

沒覺得sw鈑金需要改動啊

newmorn · 發表于 2016-10-23 16:56:57

sw工程圖里面的平板形式不就是展開圖嗎？這都要寫代碼呀？

機械路慢 · 發表于 2016-10-23 17:46:39

樓主，這是？代碼要放到哪里？

befuture · 發表于 2016-10-23 19:23:30

怎么用啊新手

hc2003 · 發表于 2016-10-23 19:49:24

樓主好人做到底，說明一下怎么使用啊

DaveChan · 發表于 2016-10-24 08:23:43

本帖最后由 DaveChan 于 2016-10-24 08:54 編輯

newmorn 發表于 2016-10-23 16:56: B. K/ o9 d9 ^; ~7 S. W
sw工程圖里面的平板形式不就是展開圖嗎？這都要寫代碼呀？

代碼替代了繁瑣的點擊另存為過程，利用代碼做成宏按鈕，一鍵保存平板形式為dwg/dxf下面動畫為另存為輸出過程和宏代碼輸出過程

DaveChan · 發表于 2016-10-24 08:58:37

hc2003 發表于 2016-10-23 19:49
) V9 ?! l; f/ _# z5 ?/ t1 }樓主好人做到底，說明一下怎么使用啊

1.新建一個宏，刪除里面所有代碼
2.復制我貼的代碼到這個宏里面
3.保存此宏
4.打開一個鈑金零件(可以展開的零件)
5.運行此宏
6.自動輸出展開圖(DWG)

		自動登錄	找回密碼
密碼			注冊會員

久久久国产一区二区_国产精品av电影_日韩精品中文字幕一区二区三区_精品一区二区三区免费毛片爱