那位大俠幫我翻譯成英語？非常感謝！

一顆豆芽

1、打槽工裝調整不到位
: `5 {6 m+ V& a: Z, O1.1、各底座安裝不同軸
" P1 `+ P$ K; ~5 r$ A; S3 |1.2、零件安裝的松緊程度不適合
1.3、壓桿安裝的松緊程度不適合
1.4、打槽機空間小調整困難
2、加工前沒有檢查沖針的磨損程度
& h% I. O% s9 {& F0 Y7 g3、打槽機工裝不適合M15/M16產品加工
3.1、底座不能安裝高度為2.9mm的產品
3.2、壓桿不能固定OD＜75的產品
3.3、壓塊不能壓緊產品
, c: o- f. h* l7 }2 ?# a4、沖針切削阻力大，尺寸變化大
4.1沖針形狀不適合
6 h, v: [; ]/ |* m: c0 x8 |9 g/ M5、氣缸不穩定
3 K/ @0 f: z' z5.1、氣壓不穩定
5.2、沖針松動
5.3、氣缸松動
6、產品外徑小，剖面小裝夾困難
7、產品易塑性變形，加工困難
/ J$ @# f, @* k1 U# }8、槽尺寸測量困難

3 d3 v+ G: @+ u
兄弟的英語實在是太難了。上面這些需要給老板看，那位好心的幫幫忙啊！
8 u4 v- }9 _6 i/ [" \

唯獨懂你

In 1, playing the slot tooling adjustment does not reach the designated positionIn
1.1, the base mounting shaft
1.2, the degree of tightness for mounting parts
, t3 ]( T% t- f; r* F1 I1.3, the degree of tightness of the pressure rod is arranged forIn
* }1 S8 E1 H/ |1 r3 x, r1.4, playing the slot machine in the whole space is difficultIn
2, prior to processing did not check the degree of wear of the punch needleIn
; \  @" J" H! ~& \4 M* S3, playing the slot machine tooling is not suitable for M15\/M16 products processingIn
3.1, the base can not be installed height of 2.9mm products
$ T- j& ]3 }+ `' M. c3.2, push rod can not be fixed OD < 75 productsIn
3 h6 c/ o, e- V" _3 S' s6 W! r3.3, the pressing block can not be pressed productsIn
4 j( v/ {& h& J0 E& _% Z) B4, the punching needle big cutting resistance, dimensional change
" b9 \( s3 N3 M. X4 v0 f4.1 punch needle shape is not suitable forIn
- g, P: ~/ N9 D8 H8 s, I2 E# Q 5, the cylinder is not stableIn
5.1, the pressure of not stableIn
' L' x6 P6 b4 o' g5.2, the punching needle looseningIn
5.3, the cylinder is looseIn
6, the product of small external diameter, small difficult clamping sectionIn
9 Q; F8 v) }6 w7 a" W* x( o. ]7, the product easy to plastic deformation, difficult processing
+ R# x1 D3 P7 K4 A- x. q& h8, groove size measurement difficulties以后自己在百度上面可以翻譯，中英文翻譯就行。

baikenor

谷歌翻譯  感覺不錯    翻譯之后再翻回去可以驗證有沒有不準確的地方

一顆豆芽

非常感謝各位