[4A] 這張齒輪圖紙的技術說明，你能看出哪里需要完善？

十年一夢

大家討論一下有什么需要完善之處。

NOTES:
1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40
(AIR CRAFT QUALITY FORGING).
! J- i/ K' C2 f- U3 h9 l2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST
BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE
3 y  y: h3 f+ s* c# m9 jCONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
0 r/ I. Y. f: u# @1 w( B& @; q. D3. DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED.
INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
' ?; f0 A+ E5 Q" ?/ l% i* U4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
. r/ m4 p  w, \/ r  [: `! I3 H7 Z3 K+ F6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED
CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40.
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING.
8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF
, U3 H" p8 b4 U" \2 ]  K. zTOOL MARKS.
  W; u( c/ s. Z# ^: Y1 }10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS &
PARALLELISM TO BE WITHIN 0.254 TIR
11.GEAR ACCURACY DATA TO BE DETERMINED FROM DATUM -A- & -B- (SHAFT).
! l! V# F" B1 T6 A! X- p12.MAGNETIC PARTICLE TEST AND INSTPECT.
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
14.BURNISH MARKED AREA WITH (*).

機械神話

希望看到這張圖，機械圖紙是圖文并存的，不可分離。

itwotwo

這是你自己出圖紙給鬼佬加工的？
8 P3 Q& x/ d+ [$ c: N* s1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40.(AIR CRAFT QUALITY FORGING).
5 M! h  N2 W# L% k" {3 T! \材質應寫入材質欄，這里只要寫熱處理方式和最終硬度
$ C$ {3 ^- o' K" ?2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
這里的軸可能用axis比較合適，因為這根軸線不是實際存在的東西，同軸度本身就是個跳動值所以不用TIR。更應該直接標在圖上。
3.DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
8 E' B1 e' @: ?* |) Q' C* ^* Q半鍵連接？動平衡因該在整根軸帶齒輪的裝配體完成后整體做的，把這個要求寫在這里應該要REF一個裝配圖要求。
4 w% M) ]# j( K4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
保護刮傷正常，保護刀痕不正常。刀痕都是加工出來的，不存在保護就會消失。
$ \1 |+ R, \( s5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
？這是客戶對供應商的產品需求嗎？怎么看起來像打工做工藝分析的？
6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING
, S$ G! Z7 }% x5 f4 w& c8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
這是不是滾壓齒底的意思？用roll
9 O* p  ~! B. I4 \; v& Q9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF TOOL MARKS.
: G$ e  w3 S" l; {, q倒角處訂個1.6的光潔度就行
) d* P- v, u( O  m7 j% n10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS & PARALLELISM TO BE WITHIN 0.254 TIR
& X4 w% a" m1 K  _9 P: m同軸度，垂直度，平行度都要有參照標準的，哪有可能沒有specified啊？而且本身這3個值本身就是TIR，不需要說明
" R. j/ m$ S6 c3 J  S12.MAGNETIC PARTICLE TEST AND INSTPECT.
探傷之后要說哪些區域有傷可接受或者全部不接受
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
7 H0 |6 s9 T5 [" _我通常會用Break all burr. Sharp edge本身在機械零件里不是缺陷，該有的地方是你設計成它有。要是日用品就不能存在sharp edge。
14.BURNISH MARKED AREA WITH (*).
' p, x( |* n6 \
5 j2 `) Q- |3 [$ w5 w老兄的東西每次看都有新發現。但是如果是一個齒輪的note，好像該有的東西全部沒有：
. i3 h% H* L' t( l) z% atop circle
root circle
addendum
6 m4 V( }6 V. R7 Jdedendum
& ]4 f2 b% L  o/ O6 o- ltooth height
pitch distance
6 d$ F  T: ~9 L# B" Q0 A- P( ~這些都應該有上下公差或者標準值
) ~1 @9 P# @/ k" @presure angle應該要指出

3 X: V5 ^, D) i0 ^4 F. @0 w. [

qdtruck

沒有圖紙怎么分析啊？樓上有圖紙了？

supperslz

無圖無真相另，另外還要說一下功用。

271211310

你需要的是真正的高手

宇宙立方

愛顯擺也是人類原罪之一

湘中人

無圖無真相！！

云飄映月

高手啊，三樓

混日子

樓主你這應該是單個零件的技術要求吧？我覺得第三條動平衡應該去掉，單個零件的在這沒什么用；第五條磨削余量沒必要寫在這個里面吧，畢竟是工藝要求；另外，你要求表面刀紋看不出，那就直接定個粗糙度Ra1.6以下，這個可去參考粗糙度標準樣塊；第十條未注同心度0.254你有和第三條校核沒？單位是英制還是公制？有必要到小數點后三位？還有最后那條不太清楚你要干什么。