求翻譯

jackline · 發表于 2011-6-30 00:03:22

外語不精，求達人翻譯，謝謝

1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm

2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm，實測0.05mm
3：直線度超差：實測導軌止口直線度0.26mm（中凹）
4：尺寸超差：圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm
5：裝配基準面有2處補焊，凸0.03mm（長15mm寬5mm）附照片

神奇寶貝 · 發表于 2011-7-5 11:16:19

1.Perpendicularity is out of tolerance: drawing's requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.
3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)
4. Dimension is out of tolerance: drawing's requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.
5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.

jackline · 發表于 2011-7-7 20:06:32

回復 jackline 的帖子

受益匪淺，灰常感謝

還想問個問題：尺寸超差，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎？

神奇寶貝 · 發表于 2011-7-8 12:37:40

jackline 發表于 2011-7-7 20:06 1 H5 S/ Q9 z! h* K
回復 jackline 的帖子
" ]. t" Q8 l) o, E* C; w+ @' p; j
4 e F1 M) }0 b5 a# X受益匪淺，灰常感謝

沒用過，也沒聽別人這樣用過

采彡銫莎氵莫 · 發表于 2011-9-13 08:18:51

是和公司有關的，又學習了

wugqtop · 發表于 2011-9-23 13:42:19

jackline 發表于 2011-7-7 20:06
; f* q( R( z9 H0 d O) O: t回復 jackline 的帖子
3 N3 [0 j; E: O3 p$ F" ~5 e* ^* N+ [* n
受益匪淺，灰常感謝

dimension out of tolerance

kason127 · 發表于 2011-9-26 17:16:44

用google翻譯好了！！

		自動登錄	找回密碼
密碼			注冊會員

久久久国产一区二区_国产精品av电影_日韩精品中文字幕一区二区三区_精品一区二区三区免费毛片爱

求翻譯