本帖最后由 數控散人 于 2010-5-9 11:58 編輯
1 ^, ^! I; t% o; M; @
2 b( Y6 M; n# f& k0 ~FANUC Series 0 -MODEL D
( k: v" |* `4 Q" V- \" p1 GFANUC Series 0 Mate-MODEL D: L7 h& C; g( O& V
維修說明書! E1 m8 e% j9 U e2 A( C' U; @
$ @- e8 F/ d( R8 a) Z- f
目錄
2 ?9 Z* F* `4 Z* e* [......
: F: k% X! _* ]( ?/ o: r6 數字伺服..................................................................................... 336
" k' |4 s6 y- `2 \# x9 N. S. r6.1 伺服參數的初始設定方法 .................................................................... 337
0 b- \. l" ]0 i# D6.2 FSSB數據的顯示和設定畫面................................................................... 3478 W7 t" S5 K8 p/ e- L8 \8 B" z
6.3 伺服調整畫面............................................................................... 355
7 ]6 s7 q! ?( V: _3 Z6.3.1 參數的設定................................................................................355
8 `, t9 y6 I9 T* w2 \$ X6.3.2 顯示伺服調整畫面..........................................................................355
: E& r, r7 X6 B9 G2 r4 u6.3.3 與放大器和電機相關的報警..................................................................357
# n( `; s& A# l% ]! @ D+ N5 l6.3.4 αi 脈沖編碼器相關的報警...................................................................3584 x% K# A- x0 [" q F: E
6.3.5 與串行脈沖編碼器通信相關的報警............................................................359
" l: W @5 q! Z9 n0 q# i6.3.6 與斷線相關的報警..........................................................................359
7 _8 U9 \) K* c5 h6.3.7 參數非法報警..............................................................................360
; S' G! O/ m+ p) X6.3.8 其他報警..................................................................................360
" [* |) v, r" V. c( x6 J3 v6.4 調整返回參考點位置（擋塊方式）............................................................. 362
' a& ^. Z1 M) g6.5 無擋塊參考點設定........................................................................... 366
$ q' K7 d8 G: q# q( W) G6.6 αi 伺服的警告接口.......................................................................... 3684 B: R- P8 G5 m W( h2 |( A
6.7 αi 伺服信息畫面............................................................................ 369: {" ^* K3 c7 y+ b3 Y5 C
7 AC 主軸...................................................................................... 373! t9 }) h8 V2 h( H3 Q R& E
7.1 串行接口AC 主軸............................................................................ 374* \9 L* @: `1 t* I2 R7 m2 u4 V
7.1.1 主軸控制概要..............................................................................3746 j3 c1 x! D" p6 h4 _% r# t
7.1.1.1 M系列齒輪切換方式A (參數SGB (No.3705#2 = 0))............................................375
& A) X9 T! |- ~& }# [$ B8 M7.1.1.2 M系列齒輪切換方式B (參數SGB (No.3705#2 = 1))............................................375$ s9 T( s5 m8 a( C
7.1.1.3 T系列.................................................................................. 375) h r, K L# b( x- j2 ^
7.1.2 主軸設定調整畫面 .........................................................................376- g( J/ y) _, R0 V7 N% C
7.1.2.1 顯示方法............................................................................... 376. f* \$ z7 u. Y' Z& w
7.1.2.2 主軸設定畫面........................................................................... 3778 h& X/ [9 ]) n: X5 j5 m
7.1.2.3 主軸調整畫面........................................................................... 378
/ N) M0 z2 {5 E& c7.1.2.4 主軸監控畫面........................................................................... 380
" A# _: J4 n# v. {6 H+ q7.1.2.5 與調整畫面上的運行方式對應的參數號......................................................382
- n5 j: V3 Q3 k+ ~6 r......* q5 D7 Q. \4 z$ o; g; K$ _
$ ~, c! X; Y) ]1 a. k$ G8 Z' v[ 本帖最后由 數控散人 于 2009-3-10 09:31 編輯 ] |
發表于 2009-3-10 09:25:23
QQ好友和群
QQ空間
