不銹鋼磨砂要求#4

風云笑

不銹鋼表面要求磨砂也就是拉絲，要求達#4效果，對應的多少目啊，據說很高啊
3 j$ {5 p7 r( _9 O1 r3 R

遠祥

有沒有實物圖片可以說明。

風云笑

JJFJJMUDHZ 發表于 2019-4-9 10:58
6 s% S- T. j* u8 K+ _2 z; S. F. k那叫NO.4.  不是#4.  NO.4拉絲的標準就是雪花砂。  除了NO.4還分WSB跟DSB兩個標準

. u" G2 o* d+ `5 i$ ^7 \# U! C; N% X我們上次送樣，是直拉絲的，老外那邊也沒說什么。直拉絲和雪花絲，是使用的設備不一樣，還是砂帶不一樣啊
5 l% `' q) l; X8 f, @, ?

JJFJJMUDHZ

風云笑 發表于 2019-4-9 10:52
這英文寫的#4，指的國內什么標準呢

那叫NO.4.  不是#4.  NO.4拉絲的標準就是雪花砂。  除了NO.4還分WSB跟DSB兩個標準

風云笑

JJFJJMUDHZ 發表于 2019-4-9 10:42
, [4 l1 {) `; k這個多少目是跟各工廠的砂帶有關的。  我們廠是120跟180目

/ P8 ~! f. p" L這英文寫的#4，指的國內什么標準呢

JJFJJMUDHZ

這個多少目是跟各工廠的砂帶有關的。  我們廠是120跟180目

風云笑

JJFJJMUDHZ 發表于 2019-4-9 10:35
) h1 Z& b+ \4 S8 k# ]( \你說的是NO.4吧？   也就是雪花砂

#4磨砂表面具體信息，磨砂機打磨的時候，分不分？怎么實現是#4磨砂表面

/ w! Y. J+ h7 C1 h7 w9 [No. 4 Finish is characterized by short, parallel polishing lines, which extend uniformly along the length of the coil. It is obtained by mechanically polishing a No. 3 finish with gradually finer abrasives. Depending on the requirements of the application, the final finish can be anywhere between 120 and 320 grit. Higher grit numbers produce finer polishing lines and more reflective finishes. The surface roughness is typically Ra 25 micro-inches or less. This general-purpose finish is widely used for restaurant and kitchen equipment, storefronts and food processing and dairy equipment. If a fabricator needs to blend in welds or do other refinishing, the resulting polishing lines are usually longer than on product polished by a producer or toll-polishing house

幫看看呢，是雪花砂嗎，還分多少目嗎
$ F6 w3 \# e! T, F

JJFJJMUDHZ

你說的是NO.4吧？   也就是雪花砂