久久久国产一区二区_国产精品av电影_日韩精品中文字幕一区二区三区_精品一区二区三区免费毛片爱

機械社區

標題: 求翻譯 [打印本頁]
作者: jackline    時間: 2011-6-30 00:03
標題: 求翻譯
外語不精，求達人翻譯，謝謝1 v6 f( x  G+ T* k- `1 E
* ^4 s( s& |- b+ m6 k6 A( L+ D
1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm
3 a" ?" ~1 p8 ~$ f
2 k0 l" M$ Y) M% u1 H+ e2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm，實測0.05mm
2 _( U; t& C' H4 W3 I1 E2 ?3 N+ k3：直線度超差：實測導軌止口直線度0.26mm（中凹）& o% y  G. ]! W# v. z' x" B+ R3 i$ `
4：尺寸超差：  圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm6 }$ V1 i0 `  B
5：裝配基準面有2處補焊，凸0.03mm（長15mm寬5mm）附照片
; p5 o; T$ W; e* g5 I4 ]4 s0 u
作者: 神奇寶貝    時間: 2011-7-5 11:16
1.Perpendicularity is out of tolerance: drawing's  requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
" @$ G4 @& o' ~& B, ]+ ?9 h2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.7 [- G$ G6 N' s% o
3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)$ _' d" @+ k0 T/ G, e* r
4. Dimension is out of tolerance: drawing's  requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.+ w: a7 F( C2 t! I0 t6 B
5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.
作者: jackline    時間: 2011-7-7 20:06
回復 jackline 的帖子
, t" ~- o+ @4 C  F; `9 O" N- n' I3 V" t
受益匪淺，灰常感謝
! v1 V, U+ f# p( b# ~還想問個問題：尺寸超差，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎？
' A: ]( I! p$ b( ^% X# l" ~; R: t, p! K4 i1 ^2 h
; }$ n8 U4 \' J0 c
作者: 神奇寶貝    時間: 2011-7-8 12:37
jackline 發表于 2011-7-7 20:06
6 i) j( G. ^9 z3 m* [) J回復 jackline 的帖子) u8 E9 @- [# u1 d% d' K2 U: u% m
, g) p+ h' i5 B4 Z
受益匪淺，灰常感謝

- T% ]1 ^. @  [# R$ n4 s8 L8 ^沒用過，也沒聽別人這樣用過
作者: 采彡銫莎氵莫    時間: 2011-9-13 08:18
是和公司有關的，又學習了
作者: wugqtop    時間: 2011-9-23 13:42
jackline 發表于 2011-7-7 20:06
/ l6 ?( H- ?3 a( H0 j& ~* F回復 jackline 的帖子2 y% ^8 _0 }1 P0 m9 `

, N2 \- ?, l4 y2 F* ], n8 e6 g" D* K1 u受益匪淺，灰常感謝

' ~/ U( j* \( g9 P' T  z( B0 L- Edimension out of tolerance
$ c; S/ N9 @& q$ _( v
作者: kason127    時間: 2011-9-26 17:16
用google翻譯好了！！



歡迎光臨 機械社區 (http://www.ytsybjq.com/) Powered by Discuz! X3.5